periph_conf.h File Reference

Peripheral MCU configuration for the nucleo-f103rb board. More...

Detailed Description

Peripheral MCU configuration for the nucleo-f103rb board.

Author
Víctor Ariño victo.nosp@m.r.ar.nosp@m.ino@t.nosp@m.riag.nosp@m.nosys.nosp@m..com

Definition in file periph_conf.h.

#include "periph_cpu.h"
+ Include dependency graph for periph_conf.h:

Go to the source code of this file.

Clock settings

Note
This is auto-generated from cpu/stm32_common/dist/clk_conf/clk_conf.c
#define CLOCK_CORECLOCK   (72000000U)
 
#define CLOCK_HSE   (8000000U)
 
#define CLOCK_LSE   (1)
 
#define CLOCK_AHB_DIV   RCC_CFGR_HPRE_DIV1
 
#define CLOCK_AHB   (CLOCK_CORECLOCK / 1)
 
#define CLOCK_APB1_DIV   RCC_CFGR_PPRE1_DIV2 /* max 36MHz */
 
#define CLOCK_APB1   (CLOCK_CORECLOCK / 2)
 
#define CLOCK_APB2_DIV   RCC_CFGR_PPRE2_DIV1 /* max 72MHz */
 
#define CLOCK_APB2   (CLOCK_CORECLOCK / 1)
 
#define CLOCK_PLL_PREDIV   (1)
 
#define CLOCK_PLL_MUL   (9)
 

Timer configuration

#define TIMER_0_ISR   isr_tim2
 
#define TIMER_1_ISR   isr_tim3
 
#define TIMER_NUMOF   ARRAY_SIZE(timer_config)
 
static const timer_conf_t timer_config []
 

UART configuration

#define UART_0_ISR   (isr_usart2)
 
#define UART_1_ISR   (isr_usart1)
 
#define UART_2_ISR   (isr_usart3)
 
#define UART_NUMOF   ARRAY_SIZE(uart_config)
 
static const uart_conf_t uart_config []
 

Real time counter configuration

#define RTT_IRQ_PRIO   1
 
#define RTT_DEV   RTC
 
#define RTT_IRQ   RTC_IRQn
 
#define RTT_ISR   isr_rtc
 
#define RTT_MAX_VALUE   (0xffffffff)
 
#define RTT_FREQUENCY   (16384) /* in Hz */
 
#define RTT_PRESCALER   (0x1) /* run with ~16 kHz Hz */
 

I2C configuration

Note
This board may require external pullup resistors for i2c operation.
#define I2C_0_ISR   isr_i2c1_ev
 
#define I2C_1_ISR   isr_i2c2_ev
 
#define I2C_NUMOF   ARRAY_SIZE(i2c_config)
 
static const i2c_conf_t i2c_config []
 

SPI configuration

Note
The spi_divtable is auto-generated from cpu/stm32_common/dist/spi_divtable/spi_divtable.c
#define SPI_NUMOF   ARRAY_SIZE(spi_config)
 
static const uint8_t spi_divtable [2][5]
 
static const spi_conf_t spi_config []
 

Variable Documentation

◆ i2c_config

const i2c_conf_t i2c_config[]
static
Initial value:
= {
{
.dev = I2C1,
.speed = I2C_SPEED_NORMAL,
.scl_pin = GPIO_PIN(PORT_B, 8),
.sda_pin = GPIO_PIN(PORT_B, 9),
.bus = APB1,
.rcc_mask = RCC_APB1ENR_I2C1EN,
.clk = CLOCK_APB1,
.irqn = I2C1_EV_IRQn
},
{
.dev = I2C2,
.speed = I2C_SPEED_NORMAL,
.scl_pin = GPIO_PIN(PORT_B, 10),
.sda_pin = GPIO_PIN(PORT_B, 11),
.bus = APB1,
.rcc_mask = RCC_APB1ENR_I2C2EN,
.clk = CLOCK_APB1,
.irqn = I2C2_EV_IRQn
}
}
APB1 bus.
#define GPIO_PIN(x, y)
Define a CPU specific GPIO pin generator macro.
Definition: periph_cpu.h:35
normal mode: ~100 kbit/s
Definition: i2c.h:183
port B
Definition: periph_cpu.h:37

Definition at line 141 of file periph_conf.h.

◆ spi_config

const spi_conf_t spi_config[]
static
Initial value:
= {
{
.dev = SPI1,
.mosi_pin = GPIO_PIN(PORT_A, 7),
.miso_pin = GPIO_PIN(PORT_A, 6),
.sclk_pin = GPIO_PIN(PORT_A, 5),
.cs_pin = GPIO_UNDEF,
.rccmask = RCC_APB2ENR_SPI1EN,
.apbbus = APB2
},
{
.dev = SPI2,
.mosi_pin = GPIO_PIN(PORT_B, 15),
.miso_pin = GPIO_PIN(PORT_B, 14),
.sclk_pin = GPIO_PIN(PORT_B, 13),
.cs_pin = GPIO_UNDEF,
.rccmask = RCC_APB1ENR_SPI2EN,
.apbbus = APB1
}
}
APB1 bus.
#define GPIO_UNDEF
Definition of a fitting UNDEF value.
port A
Definition: periph_cpu.h:36
APB2 bus.
#define GPIO_PIN(x, y)
Define a CPU specific GPIO pin generator macro.
Definition: periph_cpu.h:35
port B
Definition: periph_cpu.h:37

Definition at line 194 of file periph_conf.h.

◆ spi_divtable

const uint8_t spi_divtable[2][5]
static
Initial value:
= {
{
7,
6,
4,
2,
1
},
{
7,
7,
5,
3,
2
}
}

Definition at line 177 of file periph_conf.h.

◆ timer_config

const timer_conf_t timer_config[]
static
Initial value:
= {
{
.dev = TIM2,
.max = 0x0000ffff,
.rcc_mask = RCC_APB1ENR_TIM2EN,
.bus = APB1,
.irqn = TIM2_IRQn
},
{
.dev = TIM3,
.max = 0x0000ffff,
.rcc_mask = RCC_APB1ENR_TIM3EN,
.bus = APB1,
.irqn = TIM3_IRQn
}
}
APB1 bus.

Definition at line 61 of file periph_conf.h.

◆ uart_config

const uart_conf_t uart_config[]
static
Initial value:
= {
{
.dev = USART2,
.rcc_mask = RCC_APB1ENR_USART2EN,
.rx_pin = GPIO_PIN(PORT_A, 3),
.tx_pin = GPIO_PIN(PORT_A, 2),
.bus = APB1,
.irqn = USART2_IRQn
},
{
.dev = USART1,
.rcc_mask = RCC_APB2ENR_USART1EN,
.rx_pin = GPIO_PIN(PORT_A, 10),
.tx_pin = GPIO_PIN(PORT_A, 9),
.bus = APB2,
.irqn = USART1_IRQn
},
{
.dev = USART3,
.rcc_mask = RCC_APB1ENR_USART3EN,
.rx_pin = GPIO_PIN(PORT_B, 11),
.tx_pin = GPIO_PIN(PORT_B, 10),
.bus = APB1,
.irqn = USART3_IRQn
}
}
APB1 bus.
port A
Definition: periph_cpu.h:36
APB2 bus.
#define GPIO_PIN(x, y)
Define a CPU specific GPIO pin generator macro.
Definition: periph_cpu.h:35
port B
Definition: periph_cpu.h:37

Definition at line 88 of file periph_conf.h.